Complete set of the 12V swiing® ingenious EVO ignition with built-in 60W light coil and starter wheel. Suitable for your Zündapp Belmondo, Bergsteiger M25/M50, as well as Alpa Spezial 3000 or Alpa Black River moped, moped and small motorcycle with 247 engine.
The racing ignition comes complete with CNC-milled fan wheel and constantly supplies your cylinder with the optimum cooling.
With the two 100 g and 250 g additional weights (optional), you can increase the flywheel mass so that the engine runs more smoothly at idle and starting is easier when stationary. Depending on the application, the flywheel is supplemented with 100, 250 or 350 grams (both disks) of additional mass.
Advantages of the EVO tuning ignition:
- Always a constant, strong spark
- No more misfires
- One-time adjustment
- Little to no wear
- Large adjustment range thanks to long slots
The following special features characterize this ignition:
- From the factory more flywheel mass than HPI ignitions, therefore smoother engine idling (382 grams)
- Fine balanced flywheel for less vibration
- Trigger thread with normal M26x1.5 mm pitch, so normal Bosch/Ducati flywheel pullers can be used
- Easy adjustment of the ignition timing
- The stator was designed for high heat loads;designed for high heat loads, no more failures due to overheating
- optimized ignition curve (adjustment 12° - 14°)
- Light voltage: 12 Volt
- Light output: 60 Watt
- Ø outside flywheel: 75 mm
- Flywheel cone: ratio 1:5 (standard for Puch & Sachs crankshafts)
- Ø outer stator plate: 90 mm
Installation instructions:
- Right-turning engines: Set piston to TDC, marking on the base plate at 11 o'clock (to the left of the swiing logo) must match the marking on the flywheel, this achieves a timing of 2 mm before TDC.
- Left-turning engines: Set the piston to TDC, the marking on the base plate at 13 o'clock (to the right of the swiing logo) must match the marking on the flywheel; this achieves a timing point of 2 mm before TDC.
- Flywheel tightening torque: 37 - 39 Nm (no keyway available)
- The CDI and ignition coil must be supplied with a good ground (earthing), otherwise they can be damaged within a short time.
- The lighting system should also be equipped with a 12 V voltage regulator.
Correct pinning of the Superseal plug:
- 1 = black
- 2 = blue
- 3 = white
Attention: Under no circumstances should excessively long screws be used to mount the fan wheel, as otherwise the stator winding may be damaged. A suitable screw set is included in the scope of delivery.
When purchasing this complete set, there is a substantial percentage off the retail price of the individual parts.
Exceptional product for the highest demands of the quality brand swiing®.
The set includes the following fixed parts:
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: black · Ø outside: 120 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm, 5.5 mm · Ø bolt circle: 48 mm, 70 mm, 100 mm · Number of fixing points: 10 pcs · Height: 13.5 mm · Weight: 87 g
Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Thread type: M6x1 (standard thread) · Drive: Slot · Number of components: 6 pcs
Manufacturer: swiing® ingenious parts
Details
| Manufacturer | swiing® ingenious parts |
| Tension | 12 V |
| Light coil voltage | 12 V |
| Performance | 60 W |
| Direction of rotation | any |
| Ø mounting plate | 90 mm |
| Ø Internal flywheel | 63.5 mm |
| Number of fixing points | 3 pcs |
| Ø Flywheel outside | 75 mm |
| Mounting type | Screws |
| Area of application | Tuning, High End, Racing |
Suitable for the following models
| Zündapp Belmondo |
Accessories & related products
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Component group Carburetor: Spraying · Ø cable: 5 mm · Ø cable: 7 mm · Pony OEM number: A2099 · Sachs OEM no.: 0265 100 00
EUR 10.20
GPO flywheel trigger M26x1.5 / M22x1.5 | Puch, Sachs, Beta 521
Width across flats (trigger): 27 mm · Manufacturer: GPO · Clamping depth: 10 mm · Area of application: (Dis)assembly tool · Width across flats Screw: 19 mm · Material: Steel · Number of components: 1 pcs · Total length: 55 mm · Total length: 75 mm · Surface: blackened · Thread type: MF22x1.5 (fine pitch thread) · Thread type: MF26x1.5 (fine pitch thread) · Strength class: 8.8
EUR 11.50
Loctite 243 medium-strength threadlocker 10 ml
Manufacturer: Loctite · Area of application: Chemistry · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Type of application: 1K · Color: blue · Contents [ml]: 10 ml · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Adhesion: medium strength · Temperature resistance (min.): -75 - 200 °C · Gap dimension (max.): 0.01 mm · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 25.50
EUR 2’550.00/l
swiing® ingenious fan wheel red (EVO, HPI, Bosch, Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: anodized · Color: red · Ø outside: 120 mm · Ø inside: 39 mm · Ø mounting hole: 6 mm · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Height: 13.5 mm · Weight: 87 g · Number of fixing points: 10 pcs
EUR 72.70
swiing® ingenious fan wheel chrome (EVO, HPI, Bosch, Ducati) | Puch X30 Velux, Sachs 503, Belmondo
Manufacturer: swiing® ingenious parts · Material: Aluminum · Surface: chrome-plated · Ø inside: 39 mm · Ø outside: 120 mm · Color: Chrome · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Ø mounting hole: 6 mm · Number of fixing points: 10 pcs · Height: 13.5 mm · Weight: 87 g
EUR 80.20
DENSO (IWF24 / IWF27) Spark plug short thread U-Groove Iridium
Manufacturer: DENSO · Candle thread type: short · Spark plug socket: M4 · Electrode material: Iridium · Suppressed: No · Area of application: Cross · Area of application: High End · Area of application: Tuning · Width across flats SW: 21 mm · Thread type: MF14x1.25 (fine pitch thread)
EUR 30.20
Moped fans like you also bought:
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Valve type: TR4 Auto valve · Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Tire height [%]: 100 · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 "
EUR 11.50
Handlebar stem 35 cm curved with chrome strut
Manufacturer: Made in Germany · Material: Steel · Surface: chrome-plated · Color: Chrome · Clamping diameter: 25 mm · Width: 710 mm · Height: 350 mm · Length handlebar ends: 140 mm · Crossbar: Yes · Ø outside: 22 mm · Mounting type: Front boom mounting
EUR 40.20
swiing® ingenious fan wheel black (EVO, HPI, Bosch,Ducati) | Puch X30 Velux / Sachs 503 / Belmondo
Manufacturer: swiing® ingenious parts · Weight: 87 g · Material: Aluminum · Color: black · Height: 13.5 mm · Surface: anodized · Ø bolt circle: 48 mm · Ø bolt circle: 70 mm · Ø bolt circle: 100 mm · Ø mounting hole: 5.5 mm · Ø mounting hole: 6 mm · Ø inside: 39 mm · Ø outside: 120 mm · Number of fixing points: 10 pcs
EUR 69.70
Collection only possible with online purchase and appointment.
